timesnanax.blogg.se

Hp Mediasmart Server Ex470 Recovery
hp mediasmart server ex470 recovery















  1. #HP MEDIASMART SERVER EX470 RECOVERY SOFTWARE RELATED TO#
  2. #HP MEDIASMART SERVER EX470 RECOVERY PASSWORD AND SOME#

When attempting reinstall of software, a dialogue box appears saying the Home Connector Software is already installed.I have an ex470. Went through recovery process uninstalling all software related to server. Attempting to recover HP MediaSmart server on an upgraded Win10 desktop. Old title: hp mediasmart server ex470.

Get answers from your peers along with millions of IT pros who visit Spiceworks. Also, I think the MicroServer is quieter than the MediaSmart (at least the ex475 that I had)HP MediaSmart EX475 SMI recovery files. But it’s still a cute little form factor. I took this opportunity to get an HP ProLiant MicroServer, plus it does at least RAID1 (Mirror) where the MediaSmart or DataVault servers cannot do any form of RAID. There is no hard drive lights on but I have the power light network light.Well, I’m positive this is something that HP will not support, so don’t even think of calling them if you go down this road, but I figured it’d be fun if you wanted to continue to use the same hardware.

So if you’ve got the grey top, you’ve got a lot more work to do that isn’t covered here. Additionally you’ll have to use the EX490/495 or DataVault as Vail requires at least 2GB of RAM, which aren’t in earlier models of the MediaSmart servers (e.g. As I did it I realised my mistake and.

First you’ll need to format it and make it bootable. I’m actually using the Data Traveller by Kingston. The image is slightly bigger than 4GB, so I had to step up to an 8GB thumb drive. The first step here will be to prepare your media, usually on your client computer. In order to get motherboard’s video output on headless home server (like HP MediaSmart or Acer EasyStore) connected to the monitor you caneither buy a PCI-express 1x/4x Video card or this VGA video cable adapter so you can use the onboard video.The HP MediaSmart 47 servers will let you manage boot-up, so you can boot from a USB flash drive from which you can run repair utilities, restore the original BIOS, and perform other repair.

Hp Mediasmart Server Ex470 Recovery Password And Some

The unattend file is called cfg.ini, and needs to also be in the root of the thumbdrive with the WHS 2011 DVD image on it.Inside the cfg.ini, you’ll need to answer questions, so design your file like this:Where VAILSERVER is the name of the server, Passw0rd is the server password and some password hint is the hint to remind you of what you set your password to.In order to have the MediaSmart or DataVault boot off the Thumb Drive for installation, you’ll need to completely erase the primary hard drive (the lowest one in the MediaSmart/DataVault server).Remove the drive from the server and attach it to another PC (I used Windows 7) and then erase the primary partition. As you probably know, the MediaSmart or DataVault server doesn’t have a video input, so you’re going to need to do the install via an “unattend file”. This makes the Thumb drive and the DVD look identical in Windows Explorer. Next up you’ll have to copy the Windows Home Server 2011 DVD to the root of the disk.

Insert the USB drive into the bottom-rear USB port and disconnect all other USB devices. Connect your MediaSmart or DataVault server to power, and network. While you can most likely do a factory reset to bring back WHS v1 and get access to your data on other disks in the system, I don’t cover that detail on this blog, and don’t recommend taking that sort of risk with your data.I recommend putting the box up on the desk where you can see the Health LED light and also listen to the hard drive(s). Please note that this will erase the ENTIRE primary hard disk on your server, so make sure you have a backup of ALL your data, and customization. Installation without feedback.

I also constantly refreshed my router DHCP list so I could see when the server obtained an IP address. You should hear the hard drives during this phase. The OS installation takes ~ 8-10 minutes. The health LED will blink the aqua through the BIOS bootup, then aqua/red during the OS installation. The server should automatically boot off the USB key, format the drive and install all of the operating system files.

At this point I used “MSTSC” or Remote Desktop to connect to the server. Also, when I went to I saw the remote access site being turned off: The LED light stopped blinking aqua/red and just went back to blinking aqua when it was done. The installation of the rest of the server took ~20-25 minutes for me. I’d just leave it use the answer file, but if you left out the piece out of the answer file above, you could also just run setup from here.

Their steps helped get me over that hump, although I noticed that their cfg.ini file is a beta version, which has since been updated. Make sure you clean the system hard drive, otherwise it won’t boot to the USB disk.While I did these instructions myself, I was struggling at the location of having to format the hard drive, so kudos to the folks over at MediaSmartServer.net for the help here. Make sure you have at least 2GB of RAM, this will halt the unattended configuration. Make sure you choose a name for your server that doesn’t conflict with another name on the network, this will halt the unattended configuration Now just plug in your USB Backup drive, and set it up however you like. When you log in using the VAILSERVER\Administrator, and the password you created in the cfg.ini file, you’ll see that the server is indeed setup and ready to roll:I wouldn’t say the MediaSmart or DataVault server is as fast as my MicroServer, and it certainly is lacking 4GB of RAM, but it runs reasonably well:That’s all there is to it.

The cfg.ini file is different though as it has more required fields:You’ll want to replace the bold items above with your own. HOWEVER, if you’re the type that wants to run SBS in your house, or you want to take this risk on to leverage this hardware, the same steps above work for SBS 2011 Essentials as well. Additionally, being able to see what’s going on in a hardware failure is critical to a business, so the lack of a video card of a headless device is a show-stopper. Businesses typically want the hardware RAID functionality that the DataVault or MediaSmart doesn’t offer. They also go into details about using the EX47x series that I don’t cover here.Installing Windows Small Business Server 2011 EssentialsI targeted this post to Windows Home Server, as it’s more likely to have enthusiasts in the consumer space try this than in the business space.

For example, if you plan to use remote.contoso.com as your URL, do not use contoso.com as your DNS name for your internal network. DO NOT choose the same DNS name that you plan on using for your Remote Web Access website. Local of your internal domain name to whatever you want.

It's pretty minimum requirements, but seems to work ok.Do you know if it's working on the HP X311 and if we need to change something with cfg.ini if we use a localized built (RTM).Can you initiate installation of the RTM from RDC into an existing RC setup ?Having to blow away the system drive to force re-boot from a USB is a pain.Just a quick note: Data Traveler is made by Kingston, NOT by SanDisk -)Sebastien - I have not tested an HPX311, but you don't need to change the cfg.ini file for a localized build. I'll probably install it at my parents house, since they aren't power users or add-in crazy. Just don’t make them the same.Hi Sean, how does the HP MicroServer cope with 2011?Well, I wouldn't plan on doing any transcoding, but with 2GB of ram, it does pretty well. Or, while I haven’t tested this with SBS 2011 Essentials, I think you can choose internal.contoso.com if you absolutely must.

hp mediasmart server ex470 recoveryhp mediasmart server ex470 recovery